Arrow Cylindrical Lever Locks
Q Series cylindrical lever locks
Arrow's Q Series Grade 1 cylindrical lever locks have been engineered for years of dependable operation. The Q combines flexible installation with the optional OverDrive(TM) freewheeling feature for use in the widest possible range of applications.
Certification
All Arrow Q Series locks are U.L. and c.U.L. listed for use on 3 hour, A label or lesser doors and are certified to conform to and exceed the requirements of ANSI/BHMA A156.2, Series 4000, Grade 1.
- Federal Specification FF-H-106C
- ANSI A117.1 Accessibility Code
- California State Reference Code for levers returning to within 1/2" (12.7mm) of door surface
Features
Housing-Cold rolled steel, with zinc dichromated finish for rust resistance. Latch retractor is precision cast steel. Extra long bearing sleeve offers added support for interlocking tubes and provides for extra lever rigidity.
Requires standard 2-1/8" (53.97mm) bore through door.
Thru-Bolts-Patented flexible adaptor, an eight sided nickel steel alloy mechanism allows for universal thru-bolt location according to door preparation. The flexible mounting is accomplished without manually removing screw posts from rose insert. The flexible adaptor also engages directly with springs, which will virtually eliminate lever sag.
OverDrive(TM)-Freewheeling lever action occurs when latch retraction mechanism disengages from lever handle when handle is locked. Built-in stops in the rose insert prevent lever from traveling beyond approximately 57 degrees. Additional 40% spring power in rose insert on OverDrive(TM) side of door ensures that lever handle returns to horizontal position.
Backset-2-3/4" (69.85mm) standard. 3-3/4" (95.25mm) and 5" (127mm) available.
Latch-Brass with 1/2" (12.7mm) throw standard. 3/4" (19.05mm) throw deadlocking firelatch is available for pairs of doors. Latch housing is steel, zinc dichromate finish for corrosion resistance. 1" (25.4mm) bore in edge of door is required.
Latch Front-Brass, bronze or stainless steel. 2-1/4" (57.15mm) x 1-1/8" (28.57mm) beveled, 1/8" (3.175mm) in 2" (50.8mm).
Exposed Trim-Levers are pressure cast zinc. Streamline rose scalp of brass or bronze complements other series of lever locks.
Rose Inserts-Contain coil spring which is a permanent assembly within rose insert. The inside insert has graduating steps in two locations to prevent rose scalp from loosening. A "catch" on the outside insert prevents rose scalp from working itself loose during installation.
Strikes-Brass, bronze or stainless steel. ANSI A115.2, 4-7/8" (123.82mm) x 1-1/4" (31.75mm) curved lip strike standard. Optional 2-3/4" (69.85mm) x 1-1/8"(28.57mm) strike available. All strikes have 1-1/4" (31.75mm) lip to center dimension.
Door Thickness-1-3/4" (44.45mm).
Handing-Non-handed. Levers operate bi-directionally.
Finishes-US3,US4,US10,US10B,US26,US26D. Consult WW Locking for the availability of other non-listed finishes.
W Series cylindrical lever lock
Arrow W Series Grade 1 heavy duty levers offer an economically pleasing solution for ADA compliance. They're offered in a complete range of functions and finishes and feature three lever designs that combine contemporary and traditional elements essential to the specifier, architect or facility manager.
Certification
All Arrow W Series locks are U.L. and c.U.L. listed for use on 3 hour, A label or lesser doors and are certified to conform to the requirements of ANSI/BHMA A156.2, Series 4000, Grade 1.
- Federal Specification FF-H-106C
- ANSI A117.1 Accessibility Code
- California State Reference Code for levers returning to within 1/2" (12.7mm) of door surface
Features
Housing-Cold rolled steel, with zinc dichromated finish for rust resistance. Latch retractor is precision cast steel. Extended one piece bearing sleeve offers added support for interlocking stainless steel tubes and provides for extra lever rigidity.
Requires standard 2-1/8" (53.97mm) bore through door.
Thru-Bolts-Thru-bolted within standard 161 door preparation, which allows for easy retrofit without additional holes. Supplied with two support plates, which prevent lock from loosening when installed.
OverDrive(TM)-Freewheeling lever action occurs when latch retraction mechanism disengages from lever handle when handle is locked. Built-in stops in the rose insert prevent lever from traveling beyond approximately 57 degrees. Additional 40% spring power in rose insert on OverDrive(TM) side of door ensures that lever handle returns to horizontal position.
Backset-2-3/4" (69.85mm) standard. 3-3/4" (95.25mm) and 5" (127mm) available.
Latch-Brass with 1/2" (12.7mm) throw standard. 3/4" (19.05mm) throw deadlocking firelatch is available for pairs of doors. Latch housing is steel, zinc dichromate finish for corrosion resistance. 1" (25.4mm) bore in edge of door is required.
Latch Front-Brass, bronze or stainless steel. 2-1/4" (57.15mm) x 1-1/8" (28.57mm) beveled, 1/8" (3.175mm) in 2" (50.8mm).
Exposed Trim-Levers are pressure cast zinc. Streamline rose scalp of brass or bronze complements other series of lever locks.
Rose Inserts-Contain coil spring which is a permanent assembly within rose insert. The inside insert has graduating steps in two locations to prevent rose scalp from loosening. A "catch" on the outside insert prevents rose scalp from working itself loose during installation.
Strikes-Brass, bronze or stainless steel. ANSI A115.2, 4-7/8" (123.82mm) x 1-1/4" (31.75mm) curved lip strike standard. Optional 2-3/4" (69.85mm) x 1-1/8"(28.57mm) strike available. All strikes have 1-1/4" (31.75mm) lip to center dimension.
Door Thickness-1-3/4" (44.45mm).
Handing-Non-handed. Levers operate bi-directionally.
Finishes-US3,US4,US10,US10B,US26,US26D. Consult WW Locking for the availability of other non-listed finishes.
ML Series cylindrical levers
Arrow Patented ML Series levers offer the designer, architect and contractor simple solutions to accessibility requirements. Their clean designs, architectural finishes and available functions make them ideal for commercial applications where
Certification
All Arrow ML Series locks are U.L. and c.U.L. listed for use on 3 hour, A label or lesser doors and are certified to conform to the requirements of ANSI/BHMA A156.2, Series 4000, Grade 2.
- Federal Specification FF-H-106C
- ANSI A117.1 Accessibility Code
- California State Reference Code for levers returning to within 1/2" (12.7mm) of door surface.
General Specifications
Housing-Cold rolled steel, with zinc dichromated finish for rust resistance. Latch retractor is precision cast zinc. Extended one piece bearing sleeve offers added support for interlocking stainless steel tubes and provides for extra lever rigidity. Requires standard 2-1/8" (53.97mm) bore through door.
Thru-Bolts-Patented thru-bolt design allows for thru-bolting within standard 161 door preparations, which allows for easy retrofit without additional holes. Supplied with two support plates, which secure to face of door as well as accept thru-bolts from inside rose assembly.
OverDrive(TM)-Freewheeling lever action occurs when latch retraction mechanism disengages from lever handle when lever is locked. Built-in stops in the rose insert prevent lever from traveling beyond approximately 57 degrees. Additional 40% spring power in rose insert on OverDrive(TM) side of door ensures that lever handle return to the horizontal position.
Latch-Brass with 1/2" (17.7mm) throw. Latch housing is steel, zinc dichromate finish for corrosion resistance. 7/8" (22.225mm) bore in edge of door is required. Supplied with #K-179 sleeve for use with existing 1" (25.4mm) edge bore.
Latch Front-Brass, bronze or stainless steel. 2-1/4" (57.15mm) x 1-1/8" (28.57mm). Available with 1" (25.4mm) front latch for 2-3/8" (60.32mm) backset or 1" front for 2-3/4" (69.85mm) backset.
Exposed Trim-Levers are pressure cast zinc. Streamline rose scalp of brass or bronze complement other series of lever locks.
Rose Insert-Contain coil springs, which are permanent assemblies within rose inserts. The inside insert has graduating steps in two locations to prevent the rose scalp from loosening. A catch on the outside insert prevents rose scalp from working itself loose during installation.
Backset-2-3/4" (69.85mm) standard, 3-3/4" (95.25mm) available. Also available with 5" (127mm) backset when used in conjunction with Grade 1 latch.
Door Thickness -1-3/8" (34.92mm) to 1-3/4" (44.45mm) standard.
Handing-Non-handed.
Finishes - US3, US4, US10, US10B, US26, US26D. Consult factory for the availability of other non-listed finishes.
L Series cylindrical levers
Arrow's L Series Grade 2 cylindrical lever lock provides an economical solution to accessibility requirements. It is ideal for commercial applications where heavy-duty grade levers may not be required.
Certification
All Arrow L Series locks are U.L. and c.U.L. listed for use on 3 hour, A label or lesser doors and are certified to conform to the requirements of ANSI/BHMA A156.2, Series 4000, Grade 2.
- Federal Specification FF-H-106C
- ANSI A117.1 Accessibility Code
- California State Reference Code for levers returning to within 1/2" (12.7mm) of door surface
Features
Housing-Cold rolled steel, with zinc dichromated finish for rust resistance. Requires standard 2-1/8" (53.97mm) bore through door.
Latch-Brass or bronze with 1/2" (12.7mm) throw. Latch housing is steel, zinc dichromate finish for corrosion resistance.
Latch Front-Brass or bronze 2-1/4" (57.15mm) x 1-1/8" (28.57mm) beveled UL latches are standard. Available with 1" flat fronts for 2-3/8" backset, or 1" beveled fronts for 2-3/4" backset.
Exposed Trim-Levers are pressure cast zinc, measuring 4" in length. Roses are wrought brass or bronze with a 3-5/16" diameter. Total projection from face of door is 2-7/16".
Handing-Non-handed.
Strikes-Brass, bronze or stainless steel. #300 and #306 strikes measure 1-1/4" curved lip to center. #302 and #303 strike measure 1-3/16" lip to center dimension. Strike boxes are available.
Backset-2-3/4" (69.85mm) backset standard; 2-3/8" (60.32mm) available.
Door Thickness-1-3/8" to 1-3/4" thick. (Supplied with four mounting plates).
Cylinders-Brass, 6 pin, Arrow "A" keyway standard. Competitive keyways are also available.
Finishes-US3,US4,US10,US10B,US26,US26D. Consult factory for the availability of other non-listed
finishes.RL Series cylindrical levers
The RL Series has been enhanced to offer removable throughbolts and a wide variety of designs, finishes and functions. The RL Series cylindrical locksets are an economical value for a variety of application. Perfect for multi-family housing markets, as well as light commercial applications.
Certification
The RL Series has been designed to meet the requirements of ANSI, A156.2, Series 4000, Grade 2 UL Listed for use on 3 hour, A label single swinging doors.
RL Levers conform to ADA requirements.
Features
Construction - Cold rolled steel with zinc dichromate finish for corrosion resistance. Requires standard 2-1/8" (53.97mm) bore through door.
Backset - 2-3/8" (60.31mm) or 2-3/4" (69.85mm)
Door Thickness - Fits 1-3/8" (34.93mm) to 1-3/4" (44.45mm) doors standard.
Latch - Brass 1/2" (12.7mm) throw, UL Listed, guarded latchbolt on all locking functions
Latch Front - 1" x 2-1/4" (25.40mm x 57.15mm) for 2-3/8" backset (60.32.mm) or 1-1/8" x 2-1/4" for 2-3/4" (69.85mm) backset.
Exposed Trim - RL Levers are pressure cast zinc measuring 4-3/4" (120.65mm) in length. RL Roses are wrought brass 3-3/8" (85.73mm) diameter. Total projection from face of door is 2-1/2" (63.5mm).
Strike - 4-7/8" ANSI (123.83mm), 2-3/4" (69.85mm) T strike, or 2-1/4" (57.15mm) full lip strike.
Cylinder - Solid brass 6 pin. Arrow "A" keyway standard. C keyway optional.
Keys - 2 brass keys
Handing - Non-handed
Thru-bolts - Removable thru-bolts standard on RL Series